Robots and Cobots at Work: the 13 Checks From UKCA Marking to PUWER

Most robotics businesses are two regulated things at once. They are a manufacturer, placing machinery on a market. They are also an employer, running that same machinery in a workshop, a test cell or a customer's building. The two roles sit under different law, and the gap between them is where compliance quietly fails.
It fails in predictable places. An integrator combines three compliant units into a line and does not realise it has just manufactured a new machine. A cell is moved twelve feet and nobody re-inspects it. A cobot is sold on the promise that it needs no guarding, and the buyer takes that as a legal conclusion rather than a design claim. A demonstration unit goes to a trade fair without the controls that make an unmarked prototype lawful to show.
Two dates make this worth settling now. In Great Britain the marking position changed, and not in the direction most people assume. In the European Union the entire machinery regime is replaced on 14 January 2027, which is close enough to affect products being designed today.
Thirteen checks follow, in two halves. The first six are about placing machinery on a market. The last seven are about running it.
Placing it on the market
1. Work out which marking your market actually requires. This is the one almost everybody gets wrong. UKCA did not become compulsory in Great Britain. The government confirmed it will continue to recognise CE marking in GB indefinitely, and the Supply of Machinery (Safety) Regulations 2008 are on the list of regulations that recognition covers. For machinery sold in GB you may use UKCA or CE. The decision is now commercial, not legal.
2. Treat the EU as a separate question with a deadline. Selling into the EU is governed by EU law regardless of where you build. Regulation (EU) 2023/1230 replaces the Machinery Directive and applies from 14 January 2027, the same day Directive 2006/42/EC is repealed. The European Commission's machinery pages track implementation. Machinery being designed now will be placed on that market under the new regime, so the conformity route should be chosen against it rather than against the Directive it replaces.
3. Know whether you are shipping machinery or partly completed machinery. Partly completed machinery is covered by its own provisions in the 2008 Regulations. It does not carry a conformity marking and does not travel with a declaration of conformity. It travels with a declaration of incorporation and assembly instructions, and it must not be put into service until the assembly it goes into has itself been assessed. A robot arm shipped to an integrator is very often in this category, and labelling it as though it were finished machinery creates a problem for whoever receives it.
4. Understand when assembling makes you the manufacturer. Combining machines into a functioning line is not a neutral act. The person who puts the assembly together takes on manufacturer duties for the assembly as a whole, including the interfaces between units, which is precisely where the risk in a robot cell lives. Three CE marked units plus a conveyor does not equal a compliant line.
5. Watch for substantial modification. Government guidance is explicit that products subject to important changes, substantially changing their original performance, purpose or type, are treated as new products and must meet the requirements applying when first placed on the market. Retrofitting vision, changing a payload, adding autonomy to a machine that did not have it, or re-tasking a cell can cross that line. Refurbishment and like-for-like repair that does not change performance, purpose or type does not.
6. Get demonstrations and leasing right. Two routinely missed rules. A prototype does not need UKCA marking, but may only be shown at a trade fair or exhibition under controlled conditions: operated by experts, with restricted public contact, and with clear signage that it does not meet GB requirements and will not be made available until it does. Separately, leasing, loaning and hiring all count as making the product available. Repeated hiring does not require re-marking, but before every hire the person hiring it out must check the requirements are still met. Anyone running robotics as a service is doing this every time a unit moves.
Running it
Once machinery is in use, the Provision and Use of Work Equipment Regulations 1998 apply to the employer using it. They apply whether the machine is bought, hired, borrowed or built in-house, and they are the half of the picture a manufacturer-minded business tends to underweight.
7. Suitability is about the actual conditions. Regulation 4 requires work equipment to be suitable for its purpose, requires selection to have regard to the working conditions and risks where it will be used, and in regulation 4(3) requires equipment to be used only for operations and under conditions for which it is suitable. A robot validated in a clean test cell and deployed into a cold, wet or cluttered space has moved outside the conditions its suitability was judged against.
8. Conformity is a continuing duty, not a purchase check. Regulation 10 requires employers to ensure work equipment conforms at all times with the essential requirements that applied when it was first supplied or put into service. A machine that arrived compliant and has since had a guard removed, an interlock bypassed or a safety function disabled is no longer compliant, and the duty sits with the employer using it.
9. The guarding hierarchy still applies to cobots. Regulation 11 sets a strict order: fixed guards enclosing every dangerous part where practicable, then other guards or protection devices where that is not, then jigs, holders or similar appliances, plus the information, instruction, training and supervision necessary. "Collaborative" describes how a machine is designed to behave, not an exemption from that hierarchy. The force and speed limits that make collaborative operation safe depend on the application, the tooling and the workpiece, none of which the robot manufacturer controls.
10. Inspect after installation, and again after every move. Regulation 6(1) requires inspection where safety depends on installation conditions, both after installation before first use and after assembly at a new site or in a new location. Moving a cell across a workshop triggers this. So does redeploying a unit to a different customer site, which makes it a live and recurring duty for anyone who installs on client premises.
11. Inspect on an interval, and keep the record. Regulation 6(2) requires inspection at suitable intervals and after exceptional circumstances liable to jeopardise safety. Regulation 6(3) requires the result to be recorded and kept until the next inspection is recorded. Regulation 6(4) adds that equipment leaving your undertaking must be accompanied by physical evidence of the last inspection, which applies directly to units shipped to customers.
12. Isolation has to be usable, not merely present. Regulation 19 requires suitable means of isolating equipment from all its energy sources, and those means are not suitable unless clearly identifiable and readily accessible. Stored energy in a robot arm, pneumatics and capacitive loads all matter here. Regulation 19(3) then requires appropriate measures so that reconnecting an energy source does not expose anyone to risk, which is where unexpected restart belongs.
13. Train the people, log the machine. Regulation 9 requires adequate training for everyone who uses work equipment and separately for anyone who supervises or manages its use. Regulation 5 requires equipment to be maintained in an efficient state and in good repair, and where machinery has a maintenance log, that the log is kept up to date. Regulation 22 requires equipment to be adapted so that risky maintenance can so far as is reasonably practicable be done with the machine shut down. Our guide to work equipment maintenance covers how that duty runs in practice.
The thirteen at a glance
Need Expert H&S Guidance?
Our qualified consultants can help you implement the right health & safety measures for your business.
| Half | Checks | What governs it |
|---|---|---|
| Placing on the market | 1 to 6 | Supply of Machinery (Safety) Regulations 2008; CE recognised in GB indefinitely; Regulation (EU) 2023/1230 from 14 January 2027 |
| Running it | 7 to 13 | PUWER 1998 regs 4, 5, 6, 9, 10, 11, 19 and 22 |
Why robotics businesses hit this harder than most
The pattern we see is not carelessness. It is that the two roles are held by different people who rarely meet.
The engineering team owns conformity. It knows the standards, runs the assessment and signs the declaration. The operations side owns the workshop, the test cells and the installs. PUWER duties land on operations, but they are generated by engineering decisions, and nobody holds both halves. The result is a business with excellent technical files and no inspection records.
The second pattern is site work. A robotics company that installs on customer premises is creating duties in a building it does not control, for people it does not employ, under a regulation 6 inspection trigger that fires on every new location. Engineers frequently work alone on those installs, which is a separate problem covered in our guide to lone working in tech and AI.
The third is that deployment environments are rarely the client's cleanest space. Robotics goes into warehouse and logistics operations and manufacturing sites with their own traffic routes, racking and existing machinery, and the interface between your cell and their site is nobody's default responsibility. Our own analysis of AI and robotics labs covers the R&D end of the same problem.
Holding conformity evidence, inspection records and training in one register is the practical fix, and it is the sort of thing health and safety consultants and software solve together better than either does alone, because regulation 6(3) and regulation 5(2) are both explicitly record duties. Our health and safety audits test the machine on the floor against the paperwork, which is usually where the divergence appears.
The international picture
A robotics business selling across borders is managing several regimes at once, and the divergence is widening rather than narrowing.
Great Britain now accepts both CE and UKCA for machinery, which makes it the permissive end. The European Union is moving to Regulation (EU) 2023/1230, and its treatment of learning systems deserves attention because it is narrower than the summaries suggest.
The Regulation brings systems with fully or partially self-evolving behaviour into its stricter conformity route where that behaviour uses machine learning approaches and ensures safety functions, citing data dependency, opacity, autonomy and connectivity as the reasons. It expressly does not catch software that cannot learn or evolve and is programmed only to execute automated functions. A conventional industrial robot running fixed programs is therefore outside those provisions; a system whose safety function adapts from data is not. Where it does apply, the risk assessment must address the foreseeable intended evolution of that behaviour, and the risks arising from interactions between machines working to a common end.
That distinction is worth getting right in both directions, because over-scoping it is as expensive as missing it, and it is the reason the 14 January 2027 date matters at design stage rather than at launch.
Beyond Europe the pattern repeats with different paperwork. The United States has no single machinery marking; compliance runs through OSHA's general duty and machine guarding rules plus voluntary consensus standards, with the practical constraint often being the customer's own insurer. Several Asian and Gulf markets accept or expect CE documentation but impose their own registration and local-language instruction requirements.
The workable approach is to build one technical file around the strictest applicable requirement and then map it to each market, rather than maintaining parallel files. Our international health and safety consultants do that mapping entity by entity and product by product.
Where Arinite fits
Arinite is a firm of health and safety consultants. On this subject our work sits on the use side rather than in your technical file: risk assessments for cells and installs, PUWER inspection regimes that actually fire when a unit moves, training records that match the people doing the work, and audits that compare the machine as found against the machine as documented. Where a question is one of conformity assessment or notified body route, we say so and say why.
We have worked this way for more than 15 years, with over 1,500 businesses, across more than 50 countries and over 100,000 employees, and we retain more than 95% of the clients who start with us. Our global health and safety consultants support AI and data, IT and software and engineering businesses that build and deploy automated systems.
If you cannot today produce the regulation 6 inspection record for the last cell you relocated, that is the check worth running this week.
Related Articles
Written by
Arinite Health & Safety Consultants
Health & Safety Expert at Arinite


